Analysis of thermal stress and metal movement during welding

Objectives of study were: investigation of temperature changes caused by welding arc with analysis of temperature distribution; development of system of mathematical statements describing thermal stresses and plastic strains during welding; and development of system of mathematical solutions and computer programs for one-dimensional analysis

Discipline report on thermal analyses of M551, M552, and M553 experiments

Reduced gravity does not significantly affect the thermal histories in the M551 specimen, even if molten metal flow pattern is different from that in terrestrial conditions. Thermal histories corresponding to terrestrial experimental conditions were calculated by use of the computer programs. Heat conduction through brazing alloy (M552 experiment) is improved in the Skylab conditions, because of the increased extent, rate and uniformity of braze spreading in space. Effects of reduced gravity on heat flow in the M553 specimen are insignificant, because convection effects appear instantaneously and conduction is a governing factor on the heat flow

Thermal analysis of M552 experiment for materials processing in space

Analytical and experimental studies made of heat flow in the exothermic brazing unit in the M552 experiment are described. The emphasis of the studies was placed on heat flow in the tube and the sleeve during a period from ignition to the time when the brazing alloy solidifies. Experiments were made of three specimens tested in a ground-based laboratory. Heat flow was determined by thermocouples. The analytical study covered two phases: (1) the effect of reduced gravity on heat flow in the exothermic brazing unit; and (2) the development of analytical models. The major mode of heat transfer was conduction and the effect of gravity was minimal. Good agreements were obtained between experimental and analytical results indicating the soundness of the analytical models

Knight shift detection using gate-induced decoupling of the hyperfine interaction in quantum Hall edge channels

A method for the observation of the Knight shift in nanometer-scale region in semiconductors is developed using resistively detected nuclear magnetic resonance (RDNMR) technique in quantum Hall edge channels. Using a gate-induced decoupling of the hyperfine interaction between electron and nuclear spins, we obtain the RDNMR spectra with or without the electron-nuclear spin coupling. By a comparison of these two spectra, the values of the Knight shift can be given for the nuclear spins polarized dynamically in the region between the relevant edge channels in a single two-dimensional electron system, indicating that this method has a very high sensitivity compared to a conventional NMR technique.Comment: 4 pages, 4 figures, to appear in Applied Physics Letter

Fabrication of graphene nanoribbon by local anodic oxidation lithography using atomic force microscope

We conducted local anodic oxidation (LAO) lithography in single-layer, bilayer, and multilayer graphene using tapping-mode atomic force microscope. The width of insulating oxidized area depends systematically on the number of graphene layers. An 800-nm-wide bar-shaped device fabricated in single-layer graphene exhibits the half-integer quantum Hall effect. We also fabricated a 55-nm-wide graphene nanoribbon (GNR). The conductance of the GNR at the charge neutrality point was suppressed at low temperature, which suggests the opening of an energy gap due to lateral confinement of charge carriers. These results show that LAO lithography is an effective technique for the fabrication of graphene nanodevices.Comment: 4 pages, 4 figure

Analysis of thermal stresses and metal movement during welding

Finite element computer programs were developed to determine thermal stresses and metal movement during butt welding of flat plates and bead-on-plate welding along the girth of a cylindrical shell. Circular cylindrical shells of 6061 aluminum alloy were used for the tests. Measurements were made of changes in temperature and thermal strains during the welding process

Gate-controlled nuclear magnetic resonance in an AlGaAs/GaAs quantum Hall device

We study the resistively detected nuclear magnetic resonance (NMR) in an AlGaAs/GaAs quantum Hall device with a side gate. The strength of the hyperfine interaction between electron and nuclear spins is modulated by tuning a position of the two-dimensional electron systems with respect to the polarized nuclear spins using the side-gate voltages. The NMR frequency is systematically controlled by the gate-tuned technique in a semiconductor device.Comment: 3 pages, 4 figures, submitted to Appl. Phys. Let

Electrical polarization of nuclear spins in a breakdown regime of quantum Hall effect

We have developed a method for electrical polarization of nuclear spins in quantum Hall systems. In a breakdown regime of odd-integer quantum Hall effect (QHE), excitation of electrons to the upper Landau subband with opposite spin polarity dynamically polarizes nuclear spins through the hyperfine interaction. The polarized nuclear spins in turn accelerate the QHE breakdown, leading to hysteretic voltage-current characteristics of the quantum Hall conductor.Comment: 3 pages, 4 figures, submitted to Appl. Phys. Let

Feasibility of remotely manipulated welding in space: A step in the development of novel joining technologies

A six month research program entitled Feasibility of Remotely Manipulated Welding in Space - A Step in the Development of Novel Joining Technologies is performed at the Massachusetts Institute of Technology for the Office of Space Science and Applications, NASA, under Contract No. NASW-3740. The work is performed as a part of the Innovative Utilization of the Space Station Program. The final report from M.I.T. was issued in September 1983. This paper presents a summary of the work performed under this contract. The objective of this research program is to initiate research for the development of packaged, remotely controlled welding systems for space construction and repair. The research effort includes the following tasks: (1) identification of probable joining tasks in space; (2) identification of required levels of automation in space welding tasks; (3) development of novel space welding concepts; (4) development of recommended future studies; and (5) preparation of the final report

Nondestructive measurement of residual stresses in metals and metal structures

Nondestructive measurement of residual stress production during high strength aluminum alloy structure fabricatio